Item
Beta75X HD Whoop Quadcopter (3S)
※7/31(水)入荷予定
遂にBeta75XにHD録画ができる新シリーズが登場!
Caddx Turtle V2を搭載しフルHDの録画が可能です。
さらに従来の75Xではなく3S対応となった為、パワーに余裕が生まれ、飛行時間も伸びました!
Futaba受信機搭載
Beta75Xは現在3種類のラインナップとなります!
1.Beta75X 2S(旧型)
2.Beta75X 3S
3.Beta75X HD
※VTXの系統図はこちら
https://drive.google.com/file/d/1U6F43rFyKVbLO8y4rBwW4AAH-mbPdYtX/view?usp=sharing
BULLET POINT
Beta75X starts a new era of 3S whoop drones. With a big improvement in power, you could fly real acro, like a larger quad, but is still small enough, safe enough, and quiet enough to fly anywhere.
With the high performance STM32F411CEU6 processor FC boards and tuned Betaflight MATEKF411 (MK41) firmware, everyone could fly the Beta75X drone like a racing pro.
Experience high quality video and high-definition DVRs with the Caddx Turtle V2 on Beta75X HD version.
Durable and light enough frame is customized for the Beta75X. A total weight of 57.4g give pilots a good balance of weight and nice punch on 3S battery.
Whole drone no soldering or tinkering necessary. Customized 1103 8000KV motors with cable connectors, provide powerful thrust on 3S, just plug and play.
300mAh 3S high rate battery is recommended by default.
SPECIFICATION
Weight:57.4g (without battery)
Motors: 1103 8000KV with connector
Props: 40mm 4-blades props, 1.5mm shaft hole
Camera: CADDX Turtle V2 ( for HD DVR version)
Canopy: Canopy for Beta75X (HD DVR)
Receiver Option: Frsky XM+ / DSMX / Futaba S-FHSS / Flysky
Frame: Beta75X Frame
Recommend battery: 300mAh 3S 45C Battery
RECOMMEND BATTERY
Highly recommend the newest 300mAh 45C batteries for this small beast.
We don't DO NOT recommend the 1103 11000KV motors for 3S power because the motor may overheat or burn which will cause permanently damage on the motor or ESC.
And don't use 1103 8000KV motors for 2S power, the performance will be not as good as the 1103 11000KV motors since lack of power.
Motors Recommend Battery
1103 11000KV - 2S 350mAh Battery
1103 8000KV - 3S 300mah Battery
F4 2-4S AIO 12A FC
CPU: STM32F411CEU6 (100MHZ )
Six-Axis: MPU6000 (SPI connection)
Size: 26mm x 26mm, whoop mounting pattern
Firmware version: Betaflight MATEKF411 (MK41)
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Receiver: Support Frsky XM/XM+ Receiver/ Futaba Receiver/ Flysky Receiver/ TBS Crossfire Receiver. Add Frsky R9M Receiver and DSMX receiver since V1.2.
Support programmable LED like WS2812 etc
Built-in current sensor Weight: 5.6g
ESC
Support BLheli/BLHELI_S suite Pass-through ready
Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
Input voltage: 2S-4S Lipo
Continue current: 12A
Peak current: 13A
Firmware: BLHELI_S
Processor: SILABS EFM8BB21F16G
Motor Connectors: 1.25mm header pins connector
Factory firmware: G-H-30-16.7
CADDX TURTLE V2 CAMERA AND A01 VTX
To enjoy the powerful flight and capture HD beautiful flying video at the same time, many pilots revamped their Beta75X with HD camera. Inspired by this, we upgraded the Beta75X to 3S with Caddx Turtle V2 camera so that pilot do not need to assemble it any more and get more power on punch for acro mode. The angle for the camera is 30° and unadjustable.
Besides that, the newest A01 VTX board is lighter and perfectly suitable for canopy with switchable output power between 25mW and 200mW.
Smart audio is available for VTX remote control in default.
Output power: 25mW and 200mW (Adjustable)
Smart Audio function is included for radio control
Frequency: 5.8GHz 6 bands 48 channels, with Raceband: 5362~5945MHz
Caddx Turtle V2 camera
TV System: NTSC
Aspect Ratio: 4:3(non-changeable)
Image sensor: 1 / 2.7" CMOS sensor
遂にBeta75XにHD録画ができる新シリーズが登場!
Caddx Turtle V2を搭載しフルHDの録画が可能です。
さらに従来の75Xではなく3S対応となった為、パワーに余裕が生まれ、飛行時間も伸びました!
Futaba受信機搭載
Beta75Xは現在3種類のラインナップとなります!
1.Beta75X 2S(旧型)
2.Beta75X 3S
3.Beta75X HD
※VTXの系統図はこちら
https://drive.google.com/file/d/1U6F43rFyKVbLO8y4rBwW4AAH-mbPdYtX/view?usp=sharing
BULLET POINT
Beta75X starts a new era of 3S whoop drones. With a big improvement in power, you could fly real acro, like a larger quad, but is still small enough, safe enough, and quiet enough to fly anywhere.
With the high performance STM32F411CEU6 processor FC boards and tuned Betaflight MATEKF411 (MK41) firmware, everyone could fly the Beta75X drone like a racing pro.
Experience high quality video and high-definition DVRs with the Caddx Turtle V2 on Beta75X HD version.
Durable and light enough frame is customized for the Beta75X. A total weight of 57.4g give pilots a good balance of weight and nice punch on 3S battery.
Whole drone no soldering or tinkering necessary. Customized 1103 8000KV motors with cable connectors, provide powerful thrust on 3S, just plug and play.
300mAh 3S high rate battery is recommended by default.
SPECIFICATION
Weight:57.4g (without battery)
Motors: 1103 8000KV with connector
Props: 40mm 4-blades props, 1.5mm shaft hole
Camera: CADDX Turtle V2 ( for HD DVR version)
Canopy: Canopy for Beta75X (HD DVR)
Receiver Option: Frsky XM+ / DSMX / Futaba S-FHSS / Flysky
Frame: Beta75X Frame
Recommend battery: 300mAh 3S 45C Battery
RECOMMEND BATTERY
Highly recommend the newest 300mAh 45C batteries for this small beast.
We don't DO NOT recommend the 1103 11000KV motors for 3S power because the motor may overheat or burn which will cause permanently damage on the motor or ESC.
And don't use 1103 8000KV motors for 2S power, the performance will be not as good as the 1103 11000KV motors since lack of power.
Motors Recommend Battery
1103 11000KV - 2S 350mAh Battery
1103 8000KV - 3S 300mah Battery
F4 2-4S AIO 12A FC
CPU: STM32F411CEU6 (100MHZ )
Six-Axis: MPU6000 (SPI connection)
Size: 26mm x 26mm, whoop mounting pattern
Firmware version: Betaflight MATEKF411 (MK41)
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Receiver: Support Frsky XM/XM+ Receiver/ Futaba Receiver/ Flysky Receiver/ TBS Crossfire Receiver. Add Frsky R9M Receiver and DSMX receiver since V1.2.
Support programmable LED like WS2812 etc
Built-in current sensor Weight: 5.6g
ESC
Support BLheli/BLHELI_S suite Pass-through ready
Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
Input voltage: 2S-4S Lipo
Continue current: 12A
Peak current: 13A
Firmware: BLHELI_S
Processor: SILABS EFM8BB21F16G
Motor Connectors: 1.25mm header pins connector
Factory firmware: G-H-30-16.7
CADDX TURTLE V2 CAMERA AND A01 VTX
To enjoy the powerful flight and capture HD beautiful flying video at the same time, many pilots revamped their Beta75X with HD camera. Inspired by this, we upgraded the Beta75X to 3S with Caddx Turtle V2 camera so that pilot do not need to assemble it any more and get more power on punch for acro mode. The angle for the camera is 30° and unadjustable.
Besides that, the newest A01 VTX board is lighter and perfectly suitable for canopy with switchable output power between 25mW and 200mW.
Smart audio is available for VTX remote control in default.
Output power: 25mW and 200mW (Adjustable)
Smart Audio function is included for radio control
Frequency: 5.8GHz 6 bands 48 channels, with Raceband: 5362~5945MHz
Caddx Turtle V2 camera
TV System: NTSC
Aspect Ratio: 4:3(non-changeable)
Image sensor: 1 / 2.7" CMOS sensor
